![how to check router status how to check router status](https://flylib.com/books/1/86/1/html/2/images/13fig04.jpg)
This means that they do not need to be configured before you can use them. IMPORTANT: The following Linksys switch models: EZXS16W, EZXS88W, EZXS55W, EG008W, EG005W, SE1500, SE2500 and SE2800 are considered as non-manageable switches.
How to check router status how to#
To learn more on how to check the computer’s connectivity with the router, click here. Your computer’s firewall must be disabled as well. You should be able to do this if the router is working properly. To test if your router is working, try to ping one computer using another computer in the same network. Therefore, if you have several computers connected on a switch which happens to be connected to a router, they should belong to a single network. The IP Address of each computer in a single network is assigned by the router. Make sure that all computers connected to the switch belong to the same network To learn how to check your IP Address on a computer, click here. Make sure that the computer connected to the switch is getting an IP Address from the router or the DHCP server. For more information about LED port status indicators, click here.Ĭheck the IP Address of the connected computer(s) Make sure that the LEDs on the switch are lit and that it corresponds to the port where the router is connected to. To know more about connecting the switch to the router, click here.įollow the guidelines below to determine if the Linksys router is working properly when connected to a switch. To set the interval at which the master in the VRRP group sends VRRP Advertisement packets, run the vrrp vrid timer advertise command.This article will show you how to verify if your router is properly functioning once it is connected to a switch.īefore you verify if the router is working properly, make sure that the switch is connected to the router. Interval at which the master in the VRRP group sends VRRP Advertisement packets, in seconds.Ĭonfigured interval at which the master in the VRRP group sends VRRP Advertisement packets, in seconds. To set the preemption delay, run the vrrp vrid preempt-mode timer delay command. To disable the preemption mode, run the vrrp vrid preempt-mode disable command. If the router is the IP address owner in a VRRP group, the priority of the router in the group is displayed as 255. Priority of the master in the VRRP group. If the router is the IP address owner and this value is not configured, the default priority 100 but not 255 is displayed. Priority configured for the router using the vrrp vrid priority command. If the router is the IP address owner in a VRRP group, the running priority of the router in the group is displayed as 255. Priority of the router when the VRRP group runs. Primary IP address of the interface configured with the VRRP group on the master. To configure a virtual IP address for a VRRP group, run the vrrp vrid virtual-ip command.
![how to check router status how to check router status](https://i.pcmag.com/imagery/articles/07uQ9cisoaNxRspgRvP4eFe-28..1616598656.png)
When the interface where a VRRP group is configured becomes Down or is Administratively Down, the VRRP group status is switched to Initialize. Initialize: All VRRP groups begin in Initialize state. Master: The device functions as the master in the VRRP group.īackup: The device functions as the backup in the VRRP group. Interface where the VRRP group is configured and VRID of the VRRP group. Table 1 Description of the display vrrp command output # Display information about all VRRP groups on the router. The display vrrp command displays information about VRRP groups.
![how to check router status how to check router status](https://i.ytimg.com/vi/vJAK9kuBh8o/maxresdefault.jpg)
If this parameter is not specified, detailed information about a VRRP group is displayed.ĭisplays detailed information about a VRRP group. The VRID of the VRRP group must have been created.ĭisplays brief information about a specified VRRP group. Interface-number specifies the interface number.ĭisplays the status of a VRRP group with the specified VRID. Interface-type specifies the interface type. Interface interface-type interface-numberĭisplays the status of all VRRP groups on the specified interface. The display vrrp command displays the status and configuration parameters of VRRP groups.ĭisplay vrrp ĭisplay vrrp verbose